以磷酸二氢铵(MAP)溶液为阻燃剂,通过浸泡尾叶桉单板,研究了单板的载药量;以Ⅱ类胶合强度为指标,利用正交试验对常规胶合板生产工艺进行了优选。在此基础上,选取浸泡时间和最优生产工艺试制了阻燃桉树胶合板,并对其Ⅱ类胶合强度和燃烧性能进行了检测。结果表明:不同厚度尾叶桉单板的载药量随浸泡时间的延长呈现相似的增长规律;试验所得常规尾叶桉胶合板最优生产工艺为施胶量210 g.m-2、热压温度130℃、热压时间8 min,该条件下胶合板的Ⅱ类胶合强度达到了2.01 MPa;单板浸泡8h后,单板平均载药量为32.05 kg.m-3,所制得阻燃胶合板氧指数提高了13.9%,炭化长度减少了8.3 mm(26.2%),阻燃性能明显提高,而胶合强度也达到了Ⅱ类胶合板的国家标准。研究初步证明利用常规桉树胶合板生产工艺生产阻燃桉树胶合板是可行的。
Based on the results of more than ten year's scientific research and practice, some key techniques for cultivating poplar veneer glued wood were summarized systematically. The results were as follows: (1)Selecting appropriate poplar clones for various cultivation zones according to their growth rate and wood quality. (2)Choosing good sites being suitable for poplar clone growing (at least SI≥18?m). (3)Adopting reasonable planting density which can produce more timbers to meet the need of plywood(the tree spacing should be more than 5?m×5?m). (4)Using correct planting methods for different soil conditions, however, large seedling with 2 year old root and 1 year old stem (seedling height>4?m)were advocated. (5)Taking effective measures to tend the stand, the most effective measure was interplanting with crops. (6)Pruning was neccessary to produce non node timber, but pruning method, pruning intensity and pruning season should be controlled properly. If the 6 measures mentioned above were carried out, the poplar forests with a high yield and high quality could be ensured. In order to provied some theoretical basis for cultivating poplar veneer glued wood, 4 optimum cultivation patterns were also established using the method of two dimensions system.
热门知识
树胶酯废水-
话题： 工程造价sfghjj98e537
-
话题： 装修工程caohuaibing
精华知识
树胶酯废水-
话题： 装修工程babyfengyi
最新知识
树胶酯废水树胶酯废水相关专题
- 水泵哪个牌子好
- 连接潜污泵排水管
- 联系单湿土排水
- 楼顶天台给水管
- 楼基坑内排水
- 住宅内卫生间给水
- 住宅排水管问题
- 铸铁给水管件安装
- 铸铁给水管尺寸有哪些
- 铸铁排水管套相问题
- 以大豆油多元醇制备的硬质聚氨酯泡沫塑料的性能
- 基于S7-300PLC金属冶炼厂废水处理系统设计
- 化学除油器与稀土磁盘在轧钢废水处理中应用综合分析
- 建筑外墙涂料用核/壳苯乙烯丙烯酸酯共聚乳液
- 江苏省聚氨酯硬泡体防水保温工程技术规程发布实施
- 某高层建筑喷涂聚氨酯硬泡外墙外保温系统施工质量控制
- 建筑与环境设计用水性聚氨酯涂料应用现状及进展
- 处理300吨中医院医疗废水处理工程设计方案
- 循环利用特钢生产后的废水提高不锈钢管材强度的工艺研究
- 可热封聚酯薄膜热封型PET在香烟包装上的应用
- 两相厌氧生物反应器处理杨木P-RC APMP制浆废水
- 江西全省首个电镀废水处理国家级环保工程技术中心建成
- 玻璃/聚酯材料制成的风力发电机叶片具有更高的硬度
- 电解气浮陶瓷平板膜过滤组合工艺处理含油废水的实验
- B1级聚氨酯保温板简介
- 二甲苯不饱和聚酯树脂应用于化学工程整体地面施工
- 喷涂难燃型硬质聚氨酯泡沫屋面防水保温建筑构造图集汇总